Hydnet - the specialist in intelligent hydraulic systems
Göteborg: +46 31 499 490
|
Stockholm: +46 8 59 470 470
|
E-mail: [email protected]
0
Quotation Request
Contact
DNCAZ

4-way directional valve from Sun Hydraulics

Description

This solenoid-operated, 4-way, 2-position cartridge is a direct-acting, balanced spool directional valve. The transition between positions is closed. The closed transition greatly reduces the loss of oil when shifting which can be of particular importance in pilot control circuits.

The position switch provides confirmation that the valve is in the spring biased position. Click Here for the position sensor pin diagram

Read more ▼
  • A coil must be ordered with this cartridge. This cartridge is supplied as a sealed, factory set unit and is not field serviceable. If the assembly requires changes or service it needs to be returned to the factory. Any tampering will violate the product warranty.
  • Position switch is CE approved.
  • When torquing this cartridge into its cavity, a crow’s foot wrench or similar will be required since the position switch precludes the use of a deep socket wrench.
  • Valve capacity is based on port 3 as the inlet and port 1 as the tank. Although reverse flow is possible, the same performance cannot be guaranteed and is not recommended.
  • The solenoid tube assembly is fatigue rated for 5000 psi (350 bar) service.
  • This valve is direct actuated and requires no minimum hydraulic pressure for operation.
  • This valve utilizes a wet armature design. This means that the working fluid surrounds the armature and is exposed to the heat generated by the coil. This can be a factor if the coil is energized for long periods of time. Some fluids, notably water/glycol mixtures, break down at these temperatures over time and form varnishes that will affect the function of the cartridge.
  • A wide variety of coil termination and voltage options are available, with and without surge protection. See the CONFIGURATION section.
  • The solenoid’s unique magnetic design results in a high efficiency solenoid, yielding high spool actuating force per Watt expended, leading to reliable valve shifting.
  • Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

Technical Data

Note: Data may vary by configuration. See CONFIGURATION section.

Cavity T-31A
Series 1
Capacity 8 gpm
Capacity (metric) 30 L/min.
Maximum Operating Pressure 5000 psi
Maximum Operating Pressure (metric) 350 bar
Maximum Valve Leakage at 110 SUS (24 cSt) 10 in³/min.@3000 psi
Maximum Valve Leakage at 110 SUS (24 cSt) (metric) 160 cc/min.@210 bar
Response Time – Typical 50 ms
Switching Frequency 15,000 max. cycles/hr
Solenoid Tube Diameter .75 in.
Solenoid Tube Diameter (metric) 19 mm
Valve Hex Size 7/8 in.
Valve Hex Size (metric) 22,2 mm
Valve Installation Torque 30 – 35 lbf ft
Valve Installation Torque (metric) 41 – 47 Nm
Model Weight 2.14 lb.
Model Weight (metric) 0.97 kg.
Seal kit – Cartridge Viton: 990431006
Supply Voltage 20-30 VDC
Operating Temperature Range -25 to 80 °C
Vibration ≥ 50g, 0-500 impulses/sec
Shock >50 g, 1ms
Reverse Polarity Protection Yes
Maximum Output Load ≤ 400 mA, Duty Ratio 100%
Short Circuit Protection Yes, Load Short Unlimited
Turn On Time ≤ 25 ms
Hysteresis ≤ .002 in.
Thermal Shift – 0 to 80 °C ≤ ± .004 in.
Thermal Shift – 0 to 80 °C ≤ ± (metric) 0,1 mm
EMC DIN EN 61000-6-1/2/3/4
Connector M12 X 1 (4) Pin
Connector Environment Rating IP65

Configuration Options

Spool Configuration

C ★ Closed, Shift to Through
X ★ Cross, Shift to Through
A A to T, Shift to Through
B B to T, Shift to Through
J Open, Shift to Through
L Cross, Shift to P to A, B and T Blocked
S Regen, Shift to Through
T Tandem, Shift to Through
W A and B Bleed to T, Shift to Through
Z Motor, Shift to Through

Seal Material

N Buna-N
V Viton

Coil

211 DIN 43650-Form A, 115 VAC
212 DIN 43650-Form A, 12 VDC
212N DIN 43650-Form A, 12 VDC, no transient voltage suppression (TVS) diodes
214N DIN 43650-Form A, 14 VDC, no transient voltage suppression (TVS) diodes
223 DIN 43650-Form A, 230 VAC
224 DIN 43650-Form A, 24 VDC
224N DIN 43650-Form A, 24 VDC, no transient voltage suppression (TVS) diodes
228 DIN 43650-Form A, 28 VDC
812 Metri-Pack, 12 VDC
912 Deutsch DT04-2P, 12 VDC
912N Deutsch DT04-2P, 12 VDC, no transient voltage suppression (TVS) diodes
924 Deutsch DT04-2P, 24 VDC
924N Deutsch DT04-2P, 24 VDC, no transient voltage suppression (TVS) diodes
Cavity: T-31A
Nominal Capacity: 30 lpm (8 gpm)
Downloads
PDFSTP
Possible variants

DNCAZXN, DNCAZCN, DNCAZXV, DNCAZCV, DNCAZXN224, DNCAZCN224, DNCAZXV224, DNCAZCV224, DNCA-ZXN, DNCA-ZCN, DNCA-ZXV, DNCA-ZCV, DNCA-ZXN-224, DNCA-ZCN-224, DNCA-ZXV-224, DNCA-ZCV-224

Hydnet
EA Rosengrens gata 29
421 32 Västra Frölunda

+46 31 - 499 490
[email protected]

Products

Pages

Links

Partners