Hydnet - the specialist in intelligent hydraulic systems
Göteborg: +46 31 499 490
|
Stockholm: +46 8 59 470 470
|
E-mail: [email protected]
0
Quotation Request
Contact
RVET

Relief valve from Sun Hydraulics

Description

Ventable, pilot-operated, anti shock relief cartridges limit maximum system pressure and also limit the rate of pressure rise. The valve opens and then ramps closed at a constant speed, independent of settings and flows. These 3 port valves include a vent port (port 3) that connects between the main piston and the pilot stage to provide for remote control by other pilot or 2-way valves. The adjust screw determines the maximum (relief) setting and the minimum (threshold) setting.

Read more ▼
  • Because the modulating occurs inside the cartridge, these valves are immune to most of the problems associated with cavitation, namely noise and manifold erosion.
  • Will accept maximum pressure at port 2; suitable for use in cross port relief circuits.
  • A remote pilot relief on port 3 (vent) will control the valve below its own setting.
  • Not suitable for use in load holding applications.
  • When pressure at the inlet (port 1) exceeds the threshold setting, the valve opens to tank (port 2). The pilot section moves forward at a steady rate, increasing the setting by compressing the pilot spring. Maximum setting is achieved when the pilot section reaches a mechanical stop.
  • Valve provides protection for hydrostatic drives by reducing the jerk caused by sudden reversals. The valve is suitable for cross-port applications.
  • When used with a switching device, the valve can provide the ramp characteristic typically provided by proportional valves.
  • Small power units can be started against an anti shock relief to provide longer pump life.
  • Back pressure on the tank port (port 2) is directly additive to the valve setting at a 1:1 ratio.
  • The main stage orifice is protected against contamination.
  • Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

Technical Data

Note: Data may vary by configuration. See CONFIGURATION section.

Cavity T-2A
Series 2
Capacity 30 gpm
Capacity (metric) 120 L/min.
Maximum Operating Pressure 5000 psi
Maximum Operating Pressure (metric) 350 bar
Factory Pressure Settings Established at 4 gpm
Factory Pressure Settings Established at (metric) 15 L/min.
Control Pilot Flow 10 – 25 in³/min.
Control Pilot Flow (metric) 0,16 – 0,41 L/min.
Pressure Ramp Up Time 200 – 400 ms
Response Time – Typical 2 ms
Adjustment – No. of CW Turns from Min. to Max. setting 4.5
Valve Hex Size 1 1/8 in.
Valve Hex Size (metric) 28,6 mm
Valve Installation Torque 45 – 50 lbf ft
Valve Installation Torque (metric) 61 – 68 Nm
Adjustment Screw Internal Hex Size 5/32 in.
Adjustment Screw Internal Hex Size (metric) 4 mm
Locknut Hex Size 9/16 in.
Locknut Hex Size (metric) 15 mm
Locknut Torque 80 – 90 lbf in.
Locknut Torque (metric) 9 – 10 Nm
U.S. Patent # 6,039,070
Seal kit – Cartridge Viton: 990402006
Model Weight 1.05 lb.
Model Weight (metric) 0.47 kg.

Configuration Options

Control

C Tamper Resistant – Factory Set
L Standard Screw Adjustment

Adjustment Range

A 500 – 3000 psi (35 – 210 bar), 1000 psi (70 bar) Standard Setting
B 500 – 1500 psi (35 – 105 bar), 1000 psi (70 bar) Standard Setting
C 1000 – 6000 psi (70 – 420 bar), 1000 psi (70 bar) Standard Setting
W 1000 – 4500 psi (70 – 315 bar), 1000 psi (70 bar) Standard Setting

Seal Material

N Buna-N
V Viton
Cavity: T-2A
Nominal Capacity: 30 gpm (120 lpm)
Downloads
PDFSTP
Possible variants

RVETCAN, RVET-CAN, RVETCAV, RVET-CAV, RVETCBN, RVET-CBN, RVETCBV, RVET-CBV, RVETCCN, RVET-CCN, RVETCCV, RVET-CCV, RVETCWN, RVET-CWN, RVETCWV, RVET-CWV, RVETLAN, RVET-LAN, RVETLAV, RVET-LAV, RVETLBN, RVET-LBN, RVETLBV, RVET-LBV, RVETLCN, RVET-LCN, RVETLCV, RVET-LCV, RVETLWN, RVET-LWN, RVETLWV, RVET-LWV

Hydnet
EA Rosengrens gata 29
421 32 Västra Frölunda

+46 31 - 499 490
[email protected]

Products

Pages

Links

Partners