Hydnet - the specialist in intelligent hydraulic systems
Contact
PRFR

Pressure reducing valve from Sun Hydraulics

Description

Direct-acting, pressure reducing valves reduce a high primary pressure at the inlet (port 2) to a constant reduced pressure at port 1. These valves incorporate a damped construction for stable operation allowing the use of high reduced pressure.

Read more ▼
  • Note: This valve has no relieving capability. It should not be used in a dead-headed application. If the reduced pressure side of the circuit has very low leakage the pressure may rise significantly. The pressure rise will vary from valve to valve.
  • This type of valve, PR*R, is a good replacement for an LP*C as a normally open, restrictive compensating element if a higher pressure drop across an orifice is needed.
  • Cartridges configured with EPDM seals are for use in systems with phosphate ester fluids. Exposure to petroleum based fluids, greases and lubricants will damage the seals.
  • Full reverse flow from reduced pressure (port 1) to inlet (port 2) may cause the main spool to close. If reverse free flow is required in the circuit, consider adding a separate check valve to the circuit.
  • All spring ranges are tested for correct operation with 5000 psi (350 bar) inlet pressure.
  • Suitable for accumulator circuits since the absence of pilot control flow results in reduced secondary circuit leakage.
  • Direct operated version offers superior dynamic response compared to equivalent pilot operated models.
  • Pressure at port 3 is directly additive to the valve setting at a 1:1 ratio and should not exceed 5000 psi (350 bar).
  • Leakage specified in Technical Data is out of port 3 with a supply pressure of 2000 psi (140 bar) and the valve set at mid range. This leakage is directly proportional to pressure differential and inversely proportional to viscosity expressed in centistokes.
  • Incorporates the Sun floating style construction to minimize the possibility of internal parts binding due to excessive installation torque and/or cavity/cartridge machining variations.

Technical Data

Note: Data may vary by configuration. See CONFIGURATION section.

Cavity T-2A
Series 2
Capacity 20 gpm
Capacity (metric) 80 L/min.
Maximum Operating Pressure 5000 psi
Maximum Operating Pressure (metric) 350 bar
Factory Pressure Settings Established at 0.25 gpm
Maximum Valve Leakage at 110 SUS (24 cSt) 3 in³/min.
Maximum Valve Leakage at 110 SUS (24 cSt) (metric) 50 cc/min.
Adjustment – No. of CW Turns from Min. to Max. setting 5
Valve Hex Size 1 1/8 in.
Valve Hex Size (metric) 28,6 mm
Valve Installation Torque 45 – 50 lbf ft
Valve Installation Torque (metric) 61 – 68 Nm
Adjustment Screw Internal Hex Size 5/32 in.
Adjustment Screw Internal Hex Size (metric) 4 mm
Locknut Hex Size 9/16 in.
Locknut Hex Size (metric) 15 mm
Locknut Torque 80 – 90 lbf in.
Locknut Torque (metric) 9 – 10 Nm
Model Weight 0.79 lb.
Model Weight (metric) 0.36 kg.
Seal kit – Cartridge Viton: 990202006

Configuration Options

Control

C Tamper Resistant – Factory Set
K Handknob
L Standard Screw Adjustment

Adjustment Range

A 750 – 3000 psi (50 – 210 bar), 1000 psi (70 bar) Standard Setting
B 300 – 1500 psi (20 – 105 bar), 500 psi (35 bar) Standard Setting
D 200 – 800 psi (14 – 55 bar), 400 psi (28 bar) Standard Setting
E 100 – 400 psi (7 – 28 bar), 200 psi (14 bar) Standard Setting
S 50 – 200 psi (3,5 – 14 bar), 100 psi (7 bar) Standard Setting
W 1000 – 4500 psi (70 – 315 bar), 1000 psi (70 bar) Standard Setting

Seal Material

N Buna-N
V Viton
E EPDM

Material/Coating

/AP Stainless Steel, Passivated
/LH Mild Steel, Zinc-Nickel
Cavity: T-2A
Nominal Capacity: 80 lpm (20 gpm)
Downloads
PDFSTP
Possible variants

PRFRCAE, PRFR-CAE, PRFRCAN, PRFR-CAN, PRFRCAN/AP, PRFR-CAN/AP, PRFRCAN/LH, PRFR-CAN/LH, PRFRCAV, PRFR-CAV, PRFRCAV/AP, PRFR-CAV/AP, PRFRCAV/LH, PRFR-CAV/LH, PRFRCBE, PRFR-CBE, PRFRCBN, PRFR-CBN, PRFRCBN/AP, PRFR-CBN/AP, PRFRCBN/LH, PRFR-CBN/LH, PRFRCBV, PRFR-CBV, PRFRCBV/AP, PRFR-CBV/AP, PRFRCBV/LH, PRFR-CBV/LH, PRFRCDE, PRFR-CDE, PRFRCDN, PRFR-CDN, PRFRCDN/AP, PRFR-CDN/AP, PRFRCDN/LH, PRFR-CDN/LH, PRFRCDV, PRFR-CDV, PRFRCDV/AP, PRFR-CDV/AP, PRFRCDV/LH, PRFR-CDV/LH, PRFRCEE, PRFR-CEE, PRFRCEN, PRFR-CEN, PRFRCEN/AP, PRFR-CEN/AP, PRFRCEN/LH, PRFR-CEN/LH, PRFRCEV, PRFR-CEV, PRFRCEV/AP, PRFR-CEV/AP, PRFRCEV/LH, PRFR-CEV/LH, PRFRCSE, PRFR-CSE, PRFRCSN, PRFR-CSN, PRFRCSN/AP, PRFR-CSN/AP, PRFRCSN/LH, PRFR-CSN/LH, PRFRCSV, PRFR-CSV, PRFRCSV/AP, PRFR-CSV/AP, PRFRCSV/LH, PRFR-CSV/LH, PRFRCWE, PRFR-CWE, PRFRCWN, PRFR-CWN, PRFRCWN/AP, PRFR-CWN/AP, PRFRCWN/LH, PRFR-CWN/LH, PRFRCWV, PRFR-CWV, PRFRCWV/AP, PRFR-CWV/AP, PRFRCWV/LH, PRFR-CWV/LH, PRFRKAE, PRFR-KAE, PRFRKAN, PRFR-KAN, PRFRKAV, PRFR-KAV, PRFRKBE, PRFR-KBE, PRFRKBN, PRFR-KBN, PRFRKBV, PRFR-KBV, PRFRKDE, PRFR-KDE, PRFRKDN, PRFR-KDN, PRFRKDV, PRFR-KDV, PRFRKEE, PRFR-KEE, PRFRKEN, PRFR-KEN, PRFRKEV, PRFR-KEV, PRFRKSE, PRFR-KSE, PRFRKSN, PRFR-KSN, PRFRKSV, PRFR-KSV, PRFRKWE, PRFR-KWE, PRFRKWN, PRFR-KWN, PRFRKWV, PRFR-KWV, PRFRLAE, PRFR-LAE, PRFRLAN, PRFR-LAN, PRFRLAN/AP, PRFR-LAN/AP, PRFRLAN/LH, PRFR-LAN/LH, PRFRLAV, PRFR-LAV, PRFRLAV/AP, PRFR-LAV/AP, PRFRLAV/LH, PRFR-LAV/LH, PRFRLBE, PRFR-LBE, PRFRLBN, PRFR-LBN, PRFRLBN/AP, PRFR-LBN/AP, PRFRLBN/LH, PRFR-LBN/LH, PRFRLBV, PRFR-LBV, PRFRLBV/AP, PRFR-LBV/AP, PRFRLBV/LH, PRFR-LBV/LH, PRFRLDE, PRFR-LDE, PRFRLDN, PRFR-LDN, PRFRLDN/AP, PRFR-LDN/AP, PRFRLDN/LH, PRFR-LDN/LH, PRFRLDV, PRFR-LDV, PRFRLDV/AP, PRFR-LDV/AP, PRFRLDV/LH, PRFR-LDV/LH, PRFRLEE, PRFR-LEE, PRFRLEN, PRFR-LEN, PRFRLEN/AP, PRFR-LEN/AP, PRFRLEN/LH, PRFR-LEN/LH, PRFRLEV, PRFR-LEV, PRFRLEV/AP, PRFR-LEV/AP, PRFRLEV/LH, PRFR-LEV/LH, PRFRLSE, PRFR-LSE, PRFRLSN, PRFR-LSN, PRFRLSN/AP, PRFR-LSN/AP, PRFRLSN/LH, PRFR-LSN/LH, PRFRLSV, PRFR-LSV, PRFRLSV/AP, PRFR-LSV/AP, PRFRLSV/LH, PRFR-LSV/LH, PRFRLWE, PRFR-LWE, PRFRLWN, PRFR-LWN, PRFRLWN/AP, PRFR-LWN/AP, PRFRLWN/LH, PRFR-LWN/LH, PRFRLWV, PRFR-LWV, PRFRLWV/AP, PRFR-LWV/AP, PRFRLWV/LH, PRFR-LWV/LH